Lb-white I-34 Infraconic Spark Ignition Manual de usuario descargar pdf (Pagina 14)

1133

1. Have your gas supplier check all gas piping annually

for leaks or restrictions in gas lines. Also, at this time

have your gas supplier clean out the sediment trap on

the zone control panel of any debris that may have

accumulated.

TThhee hheeaatteerr’’ss ssuurrrroouunnddiinngg aarreeaa sshhaallll bbee kkeepptt cclleeaarr aanndd

ffrreeee ffrroomm ccoommbbuussttiibbllee mmaatteerriiaallss,, ggaassoolliinnee,, aanndd ootthheerr

ffllaammmmaabbllee vvaappoorrss aanndd lliiqquuiiddss..

3. Regulators can wear out and function improperly.

Have your gas supplier check the date codes on all

regulators installed and check delivery pressures to

the appliance to make sure that the regulator is

suitable for continued use.

4. Regulators must be periodically inspected to make

sure the regulator vents are not blocked. Debris,

insects, insect nests, snow, or ice on a regulator can

block vents and cause excess pressure at the

appliance.

5. For safety as well as for optimum performance at the

heater, it is necessary to keep the inside and the

outside of the heater free of dust, dir t or any

combustible material. If any operational component

shows signs of rust or corrosion, replace the

component immediately.

6. If any warning or instruction labels, dataplates, etc.

become lost or hard to read, replace them

immediately. Do not operate the heater until you

have all instructions and can read and understand

them.

7. Check overall condition of heater for cracked or

damaged components, loose screws or bolts, etc.

Replace any suspect components.

8. Check all hose and tubing assemblies for cracks,

abrasions or ruptures. Replace any hoses that are

suspect.

If it becomes apparent that a dark spot has formed part way

up on the inner combustion cone or a build up of debris is

occurring in the bottom of the inner cone, it will be

necessary to clean out the combustion cone assembly.

Refer to “Cleaning Instructions”.

Maintenance Instructions

Service Instructions

GENERAL

1. Close the fuel supply valve to the heater and

disconnect the heater’s electrical supply before

servicing unless it is necessary to have the valve open

and electrical supply connected for your service

procedure.

2. In servicing some components, it may be necessary to

remove optional filter kit.

3. Remove the control box cover for access to ignition

control,high limit switch, and on/off switch.

4. For reassembly, reverse the respective service

procedure. Ensure gas connections are tightened

securely.

5. After servicing, start the heater to ensure proper

operation and check for gas leaks.

CClleeaann tthhee hheeaatteerr’’ss oorriiffiicceess wwiitthh ccoommpprreesssseedd aaiirr oorr aa

ssoofftt,, ddrryy rraagg.. DDoo nnoott uussee ffiilleess,, ddrriillllss,, bbrrooaacchheess,, eettcc.. ttoo

cclleeaann tthhee oorriiffiiccee hhoolleess.. DDooiinngg ssoo wwiillll eennllaarrggee tthhee hhoollee,,

ccaauussiinngg ccoommbbuussttiioonn oorr iiggnniittiioonn pprroobblleemmss.. RReeppllaaccee tthhee

oorriiffiiccee iiff iitt ccaannnnoott bbee cclleeaanneedd pprrooppeerrllyy..

WWAARRNNIINNGG

FFiirree aanndd EExxpplloossiioonn HHaazzaarrdd

■ Do not disassemble or attempt to repair any heater

components or gas train components.

■ All component parts must be replaced if defects are

found.

■ Failure to follow this warning will result in fire or

explosions, causing property damage, injury, or death.

WWAARRNNIINNGG

BBuurrnn HHaazzaarrdd

■ Heater surfaces are extrememly hot for a period of

time after the heater has been shut down.

■ Allow the heater to cool before performing service,

maintenance, or cleaning.

■ Failure to follow this warning will result in burns

causing injury.

1 2 ... 9 10 11 12 13 14 15 16 17 18 19 ... 25 26

Comentarios a estos manuales

Sin comentarios

Lb-white I-34 Infraconic Spark Ignition Manual de usuario Pagina 14

Comentarios a estos manuales

Relacionado con productos y manuales para Radiadores Lb-white I-34 Infraconic Spark Ignition